USB - MAZ USB AUX Audio Adaptor for Mazda
Car Auto Audio MP3 Player Interface Aux In Adapter Cable Fit for Mazda USB AUX Audio Adapter 3.5mm
Feature
1.Direct Connection via CD changer Port with CD quality sound
2.Control music files from your car radio panel or steering wheel.
3.Support USB Flash, SD Card and 3.5mm jack input.
4.Building in high quality MP3/WMA decoder
5.Building in Amplifier chips
6.No signal interfere, No battery required
7.Smart design and Easy to install and use
8. Brand New and High Quality
Specifications
1. Item type: Cables, adapters & sockets
2. Voltage input: DC 12V
3. Signal-to-noise: 95DB
4. Max. current: 200mA
5. Frequency response: 20HZ-20KHZ
6. Working temperature: -10-80 Celsius degree
7. Total Harmonic Distortion:0.01%
8. Package size: 15 * 10 * 4cm
9. D/A Device: 24BIT 192KHZ
10.Total Length: about 70.8inch
Compatible with
Mazda: 2004-2008 Mazda 3 , 2002-Oct.2003 Mazda 6,2006-2008 Mazda 6 (see note 2), 2009 Mazda 6(Panasonic/Bose),2003-2008 Miata/MX5(non Bose) ,2002-2006 SPD, 2002-2003 Protégé,
2007-2008 CX7 (non Bose) , 2002-2006 Tribute, 2002->2008 Premacy,1999-2003 Mazda 323 , 2002-2011 MPV ,2003-2006 B-Series Pickup
Note:
1: Not compatible with active Satellite radios or Navigation system.
2: Not all Mazda 6 supports external CDC connection, internal modification might be needed; Mazda 6, produced from Nov. 2003 to Sep. 2005, needs to solder a jumper or a 0-ohm chip register on location L716 in its head unit.
Installation Instruction：
1. Turn off car engine and remove key from ignition (if your radio use a security code, make sure that you have the code before unplugging the radio.)
2. Disassemble the radio from the dash and find CD changer port at the back of radio.
3. Plug the USB Car Adapter connector into CD changer port firmly.(For Audi/V.W/Skoda/Seat radio, connect the GND cable to the shield of the radio)
4. Insert USB stick or SD card/ T/F Card into USB port. once the unit is installed just power on the car radio ,you can Press CD button then to check symbol of LED light being on. Meanwhile CDC,EX or CD01 will display on the radio screen( Depends on radio type). Now it will work normally.
After successfully test, re-assemble the radio, and lead USB and aux cable to proper
Package Contents
1 x USB AUX Car Audio Adapter
1x Card reader
1x User's manual
Feature
1.Direct Connection via CD changer Port with CD quality sound
2.Control music files from your car radio panel or steering wheel.
3.Support USB Flash, SD Card and 3.5mm jack input.
4.Building in high quality MP3/WMA decoder
5.Building in Amplifier chips
6.No signal interfere, No battery required
7.Smart design and Easy to install and use
8. Brand New and High Quality
Specifications
1. Item type: Cables, adapters & sockets
2. Voltage input: DC 12V
3. Signal-to-noise: 95DB
4. Max. current: 200mA
5. Frequency response: 20HZ-20KHZ
6. Working temperature: -10-80 Celsius degree
7. Total Harmonic Distortion:0.01%
8. Package size: 15 * 10 * 4cm
9. D/A Device: 24BIT 192KHZ
10.Total Length: about 70.8inch
Compatible with
Mazda: 2004-2008 Mazda 3 , 2002-Oct.2003 Mazda 6,2006-2008 Mazda 6 (see note 2), 2009 Mazda 6(Panasonic/Bose),2003-2008 Miata/MX5(non Bose) ,2002-2006 SPD, 2002-2003 Protégé,
2007-2008 CX7 (non Bose) , 2002-2006 Tribute, 2002->2008 Premacy,1999-2003 Mazda 323 , 2002-2011 MPV ,2003-2006 B-Series Pickup
Note:
1: Not compatible with active Satellite radios or Navigation system.
2: Not all Mazda 6 supports external CDC connection, internal modification might be needed; Mazda 6, produced from Nov. 2003 to Sep. 2005, needs to solder a jumper or a 0-ohm chip register on location L716 in its head unit.
Installation Instruction：
1. Turn off car engine and remove key from ignition (if your radio use a security code, make sure that you have the code before unplugging the radio.)
2. Disassemble the radio from the dash and find CD changer port at the back of radio.
3. Plug the USB Car Adapter connector into CD changer port firmly.(For Audi/V.W/Skoda/Seat radio, connect the GND cable to the shield of the radio)
4. Insert USB stick or SD card/ T/F Card into USB port. once the unit is installed just power on the car radio ,you can Press CD button then to check symbol of LED light being on. Meanwhile CDC,EX or CD01 will display on the radio screen( Depends on radio type). Now it will work normally.
After successfully test, re-assemble the radio, and lead USB and aux cable to proper
Package Contents
1 x USB AUX Car Audio Adapter
1x Card reader
1x User's manual